RLT BACTDET 05

As low as £7.70
In stock
SKU
RLT BACTDET 05
The RLT BACTDET 05 is the first stage of MGC’s Mould Eradication System. read more
Fast delivery available
Tested & verified products
50 years experience

For trade enquiries, please call us on 01372 743 334

We’re open 9:00am - 5:00pm Mon-Fri

RLT BACTDET 05

The RLT BACTDET 05 is the first stage of MGC’s Mould Eradication System. The product is soapy in consistency and supplied in concentrated form in 1 litre and 200mls bottles which should be diluted at 1:4 with warm water, however cold is OK. Apply the diluted product by brush, cloth or sponge to the infected surfaces extending the treatment 1 metre beyond visible signs of mould removing as much of the contamination as possible. This stage of the treatment will kill the mould, stop it spreading to other areas and clean the surfaces. For wallpapered surfaces, DO NOT STRIP before treating with RLT BACTDET 05, ensure that walls and ceilings that have been wallpapered are first washed down with RLT BACTDET 05, then strip the wallpaper and wash the surfaces again with a clean solution of RLT BACTDET 05.

Coverage: 200mls will treat 10-12 sq m, 1 litre will treat 45-50 sq m.

RLT BACTDET 05 is approved under COPR 1986 (as amended) by the Health & Safety Executive (HSE) for both amateur and professional use.

RLT BACTDET 05 is available in a “ready to use” trigger spray which can also be used to remove mould off cupboards, wardrobes, chest of drawers and other hard surfaces.

When dry prepare the surfaces as though you were going to decorate ensuring the surfaces are smooth, do any pointing or filling where necessary, then apply Stage 2 – RLT HALOPHEN.

For instructions on how to apply, see our videos here

APPLICATION INSTRUCTIONS FOR THE ERADICATION OF MOULD

GENERAL

This is a 3-stage treatment. All stages must be strictly adhered to.

Stage 1: RLT BACTDET 05 - cleans the surface and kills all visible signs of mould.

Stage 2: RLT HALOPHEN - forms a barrier to prevent mould infection in the fabric re-infecting the surface.

Stage 3: BIOCHECK PAINTS - fungicidal decorative finish and MGC FUNGICIDAL ADDITIVES for incorporation into wallpaper paste.

STAGE 1 - ERADICATION OF MOULD - RLT BACTDET 05

1. Wash down mould infected surfaces with RLT BACTDET 05 diluted with 4 parts of warm water using a brush, sponge or cloth. Extend treatment one metre in all directions beyond all visible signs of infection. When the solution becomes dirty make up a fresh one. Coverage must not exceed 10 square metres per diluted litre.

To affected carpets, roll back carpet and wash down floor surface with RLT BACTDET 05 solution. Spray the underside of carpets with RLT CLEARMOULD SPRAY and allow to fully dry before re-laying.

WALLPAPERED SURFACES - wash down with RLT BACTDET 05 solution prior to stripping. Bag up wallpaper, seal and remove from the premises immediately. Wash infected area again with a clean solution of RLT BACTDET 05.

This stage is essential as RLT BACTDET 05 will kill all mould spores and prevent them spreading to other areas.

2. PREPARATION

Prepare surfaces in accordance with good trade practice. Scrape off all loose or flaking paint and rub down to a sound surface.

Etch previously gloss painted surfaces with glasspaper to form a key.

All preparation work must be done before the barrier, RLT HALOPHEN, has been applied.

STAGE 2 - APPLICATION OF FUNGICIDAL BARRIER - RLT HALOPHEN

3. Apply by brush 1 coat of RLT HALOPHEN diluted with 4 parts of clean water. Extend the treatment at least one metre beyond the areas of infection in all directions and allow to dry. Coverage must not exceed 10 square metres per diluted litre.

Brush RLT HALOPHEN well in for maximum penetration. Pay special attention to corners and junctions.

In areas of heavy infection apply a second coat and allow to dry before proceeding to Stage 3.

3a. STAINING AND/OR EFFLORESCENCE - Apply by brush one liberal coat of MGC Stain Block to seal the surface and prevent any bleeding through prior to decoration.

STAGE 3 - DECORATIVE FINISH

4. EMULSION - Apply 2 coats of BIOCHECK Matt or Silk Emulsion by brush or roller at a coverage of approximately 12 square metres per litre per coat. The first coat may be diluted with 10% clean water. It is recommended that Silk is used in kitchens and bathrooms.

WALLPAPER FINISH - add 2 MGC FUNGICIDAL ADDITIVES per 5 litres of paste or size and mix well in. For embossed and lining papers incorporate MGC FUNGICIDAL ADDITIVES into paste, then apply 2 coats of BIOCHECK Matt or Silk Emulsion as above.

GLOSS FINISH - for woodwork, metal windows, etc.

Clean down, as described in Stage (1), to remove any mould contamination. Rub down previously painted surfaces with glasspaper to form a good key.

Apply 2 finishing coats of BIOCHECK WATER BASED GLOSS to all general surfaces. Bare surfaces should be primed with one coat of BIOCHECK WATER BASED GLOSS.

NOTES

1. It is recommended that when treating external walls, the entire wall(s) is treated, extending back into the room a minimum of one metre on the ceiling and adjacent walls/partitions. This will eliminate the possibility of other isolated areas of the same wall(s) being infected at a later date.

2. The use of woodchip paper is not recommended.

Help

If you require help or assistance with your order including for special colours in Biocheck Matt or Silk Emulsions and Biocheck Allweather please contact our sales office which is open Monday to Friday 9.00 am – 5.00 pm

Telephone: 01372 743334

Email: info@mgcltd.co.uk

Fax: 01372 720856

Address;

Mould Growth Consultants Limited

Unit A3

Longmead Business Centre

Blenheim Road

Epsom

Surrey

KT19 9QQ

Delivery

We will aim to process your order for despatch to you between 1-5 working days of confirming acceptance of your order. Consequently, even if you cancel your order shortly after placing it, it is possible that we may be unable to prevent goods you have ordered being despatched to you and you may then need to return them to us at your cost.

When you order your Goods, we will wherever possible, give you an indication of the day of delivery, normally 2-5 working days after confirming acceptance of your order.

Deliveries will be made by post/a carrier instructed by us to the address stipulated in your order. You must ensure that someone is present to accept delivery.

While a delivery date will be prearranged with you, please remember that it is generally not possible to contact the delivery driver once he has left the depot. As a signature is required on delivery, if you will not be at home to take the delivery, a signed note instructing the driver where to leave the goods is acceptable. Otherwise a re-delivery charge will be incurred.

 

Cancellation of Order

If you bought the Goods as a Consumer, you may cancel your order at any time before we despatch your order or before the expiry of 7 working days from the date you receive your order, not including the day you received it.

As required by the Distance Selling Regulations, details of our after-sales service and guarantees, if any, are given on our website.

If you cancel before we have sent the Goods, we will refund to you the price of the Goods and the cost of delivery, if any.

 

Goods returned

Our most important task is to ensure your absolute satisfaction. We will always strive to reach that target. However, we acknowledge that mistakes are made occasionally. This paragraph covers that possibility. If you are not wholly satisfied with the product, please tell us at the earliest opportunity:

  • Exactly what the fault is
  • The date, if relevant, when the fault became apparent
  • When and how you discovered the fault
  • How the fault affected your use of the Goods

To do this, it is essential that you follow the instructions below. These provisions apply in the event that you return Goods to us because you say they are faulty:

You must tell us by email message to (info@mgcltd.co.uk) or by letter to our land address at the top of this page you that you would like to return Goods, specifying exactly what Goods and when purchased, giving full details of the defect or other reason for return. We will then issue a returns note. If you send Goods to us without a returns note, we may not be able to identify sufficient details to enable us to attend to your complaint.

The Goods must be returned to us as soon as any defect is discovered.

So far as possible, Goods should be returned:

  • With both Goods and all packaging, as far as possible, in their original condition
  • Securely wrapped
  • Including our delivery slip
  • At your risk and cost.

Please see our full terms and conditions on the website