NON-BITUMINOUS ELASTOMERIC COMPOUND
- 10 YEAR LIFE
- INSTANT REPAIR FOR LEAKS
- CAN BE APPLIED IN WET CONDITIONS
- USE ON ANY ROOFING SURFACE
|
 |
ROOFCOAT FR10
....Is a one part moisture curing polymeric waterproofing compound which is elastomeric and has exceptional adhesion to virtually any roofing material. It has been specifically developed to provide instant waterproofing for leaking roofs, is an all-weather product and can be applied even in the wet. ROOFCOAT FR10 can be used to repair specific areas which are leaking or totally waterproof an entire roof. Large cracks, holes, tears, blisters and splits can be easily repaired using ROOFCOAT FR10 FILLER and ROOFCOAT FR10 SCRIM. The product is multi-purpose and can be utilised on a wide variety of problem areas.
The ROOFCOAT FR10 SYSTEM is easy to use, does not require special primers and gives long term protection of 10 years or more.
AREAS OF USE
- FLAT ROOFS - can be
used as a patch repair or to waterproof the whole roof area. Choice of
colour, including solar reflective white. Cracks, tears and blisters can
be repaired utilising ROOFCOAT FR10 SCRIM and ROOFCOAT FR10
FILLER.
- ASBESTOS ROOFS -
will rejuvenate corrugated sheets, waterproofing and encapsulating the
asbestos. In conjunction with ROOFCOAT FR10 SCRIM, ROOFCOAT FR10
can be used to mend split sheets.
- PORCHES - porous
leaking areas can be waterproofed easily with one coat of ROOFCOAT FR10.
- FINLOCK GUTTERS -
clean out any debris and organic matter. Gaps should be filled first with ROOFCOAT
FR10 FILLER. Apply a coat of ROOFCOAT FR10 in a 6" band at
the junction of the blocks and embed ROOFCOAT FR10 SCRIM. When dry
apply ROOFCOAT FR10 over the full length of gutter.
- VALLEY/CAST IRON
GUTTERS - ROOFCOAT FR10 can be used to waterproof gutters and repair
leaking joints. Downpipe junctions can be re-sealed with ROOFCOAT FR10
FILLER.
- PLASTIC RAINWATER GOODS
- ROOFCOAT FR10 can be used to repair splits, cracks and leaking
joints.
- FIBRE CEMENT GUTTERS
- use LICHENITE to kill any algae, moss and lichen. Remove all
silt, dirt and debris. Apply one coat of ROOFCOAT FR10 to
waterproof gutter. Repair joints as (4) above.
- FLASHINGS - leaking
defective areas can be repaired with ROOFCOAT FR10 FlLLER followed
by ROOFCOAT FR10.
- BAY WINDOW TOPS - a
very common area for leaks, which can be easily and economically rectified
with one coat of ROOFCOAT FR10 in desired colour.
- CORRUGATED TIN ROOFS
- can be used to repair old and suspect sheets. Spot prime areas of rust
with proprietary inhibitor followed by one full coat of ROOFCOAT FR10.
BENEFITS
- 10 YEAR LIFE
- WET WEATHER APPLICATION
- SINGLE COAT WATERPROOFING
- FIBRE REINFORCED COMPOUND
- AVAILABLE IN 6 COLOURS - BLACK, GREY, GREEN, TERRACOTTA, WHITE AND SOLAR REFLECTIVE ALUMINIUM
- ELASTOMERIC WHEN DRY
- OUTSTANDING ADHESION
- CAN BE USED ON A MULTITUDE OF ROOFING SURFACES
- SPECIAL FILLER AND SCRIM FOR REPAIR WORK
- VERY ECONOMICAL
|
 |
INDEPENDENT WEATHEROMETER TEST
LABORATORY REPORT
|
MATERIAL:
|
ROOFCOAT FR10
|
|
PROPERTY:
|
Ageing and Heat Resistance
|
|
TEST METHOD:
|
QUV Weatherometer
|
|
TEST SPECIMEN:
|
One coat brush applied to mineral board, dried at room
temperature.
|
|
TEST PROGRAMME:
|
Exposure cycles
4 hours UVB @ 65 Degrees Centigrade
4 hours condensation @ 50 Degrees Centigrade
|
|
RESULTS:
|
3,000 hours = surface is matt due to chalking which cleans
off to leave a good sheen. Coating is integral and providing the substrate
with protection against moisture penetration.
12,000 hours = without failure.
Colour good, surface dull due to chalking. Signs of erosion of binder and
fibres exposed. Coating still integral and intact with substrate protected
against ingress of moisture.
|
|
COMMENTS:
|
This is an accelerated ageing test which combines many factors,
such as effect of heat, ultra violet light and moisture in continuous cycles.
Because specific conditions of ageing can vary greatly, this test cannot be
quantitative. ROOFCOAT FR10 was tested in comparison with a competitor's
product which claimed to have a 10 year natural ageing span. Under our test
conditions it crazed and cracked within the first 3,000 hours of test. NB.
1000 hrs. is equivalent to 3 yrs. natural weathering.
|
|
|
